turbo leak
i found where my turbo leak was today. its coming from the tube that runs under the air filter. are there any fixes for this or wheres a good/cheap place to buy a tube. its a 05 6.0 by the way.
View ArticlePDF-standard/towing??
I just found a setting. "under truck settings (PDF): you can set to: "normal or towing". I understand what the terminology means, I just don't what each setting does. I changed it from "towing to...
View Articlecold side intake tube
how much is a intake tube thats on the drivers side? is there a metal one rather than the plastic?
View Article84 f250 4x4?
New to the forum looking for a little advice. I am looking at a 84 250 with the 6.9 runs smooth and shifts smooth heck air even works. Looks decent has typical rust on fenders but overall fair shape. I...
View ArticleCheck Engine Temp.
I have a 2007 6.0 and recently had an EGR delete kit put in after the EGR valve crapped out. I pull a utility work trailer (7000lbs.) all the time up and down the highway were I live with no problems....
View ArticleNew member. .. New to me 08 !
Howdy from SE Michigan. Been reading some great info here on the site, doing lots of research. I had recently set out to buy a used F250/350 for hauling the tractor around and such. After reading all...
View ArticleAIS or Banks Ram Air ?
I already have the Ford AIS on my 2000 7.3, but I'm adding some mods and am wondering if I need to change the intake to allow more air in? I already have 4" exhaust, am adding a Garrett Ball Bearing...
View Article86 f250 6.9l Glow Plug Controller
I discovered that my glow plug controller snapped off right at the engine block! I need to remove the broken off piece, soooooo I had a brilliant Idea to drill a hole in it and use a easy out to twist...
View Article6.9 into 7.3
I have a 93 7.3 that needs work but runs. I have a 87 6.9. That needs to be rebuilt. Can I bore the 6.9 to a 7.3? Or is the block to different. Thanks.
View ArticleToo many choices! Help me pick!!
Howdy diesel enthusiast!I'm going to go ahead and apologize in advance for the length but there I a lot of questions that need answering and a lot of important information that will go into my...
View ArticleBrakes and Wheel Bearings
Hey, First off, I was told -despite the fact that I can do it -that you should always have your brake work done at a shop. Now I have done brake work for as long as I can remember, but I am a backyard...
View ArticleNEW TO FORUM
Howdie all, I have owned my F250 with 6.7 since April and like anyone I want to know as much about this setup as possible. It has been to Maine and back this summer towing my 31ft camper which it...
View ArticleNew 2" leveling kit 05 and up $50
New in box 2" leveling kit for 05 and up 4wd only with instructions pm me if interested thanks. http://50.6.106.226/picit/1377985071.3149.iPicit.jpg
View ArticleWon't start... Fuel Pump?
1989 Ford Econoline E-350 diesel that won't start. She's had this problem for a while, but we were always able to start her by spraying starter spray into the air intake. Last time she started and ran...
View Articleturn signal volume
I put in an electronic turn signal relay (I have LED tail lights). Now I am having trouble hearing the relay clicking.( I am a little deaf). Any ideas how I can correct this?
View Article5 star eco - boost tuner for sale
I have a 5 star tuner for sale for the eco-boost engine. I ran it for 45k on my f150 eco-boost. Pm me if interested I'm asking 250.00 Thanks
View ArticleDid the rear suspension change a bit?
I could have sworn my 2000 and 2008 had u-bolts with nuts pointing up. My 2013 has the u-bolts pointing downward? Am I losing my mind or did they change slightly? I have factory helpers and a 4 inch...
View ArticleAny Ruby Red F250s with a cap/topper on the back?
I have been a Snugtop guy for 3 Superduties and dying for a new topper on my 2013, but trying to get a picture of a big giant red "strawberry" (my daughter's term to try to talk me into a tonneau) Any...
View ArticleRotor disk minimum thickness service limits ?
Guess the title says it all...But, Does anyone know or have access to a manual with this information? Mine is a 2003 E-350 (7.3) PSD. Just put new REAR Pads on and had to remove the Rotor to replace a...
View ArticleWheel studs stripping question
Hello all: I am having another problem/question. Recently had a flat tire. took it off and brought in for repair. Noticed when I put the spare tire on I had a little difficulty with one of the lug...
View Article