4r100 Filter FT113 or FT114?
I just dropped my tranny pan and changed the filter and fluid with a filter I had purchased a while back (Motorcraft FT-114). After all was done I went online to start looking for a new filter for the...
View Article04 F350 Rear Dually Axle O-ring part number
I did the brakes, new rotor and pads, new seals but I couldn't find the O-ring part number. I tried re-using the old ones and one side is holding, the other is not. Anybody have a part number? Searched...
View ArticleTruck Died at Idle, 0 Oil Pressure. HPOP?
My truck died when I left it to idle while I ran inside for less than 5 minutes. When I came back out, the keys were still in the on position, but the engine had died. I tried to crank it, and it would...
View ArticleNot Charging
ALL, My 03 is not charging. ALSO, the battery lamp on the dash is not lit. Good belt, alternator is spinning. With engine running, disconn bat cable @ alt - multimeter = 0vdc. New Alternator ? ~Mack
View ArticleToyo Open Country A-T II clearance/performance?
A friend and I are both in the market for new tires. They drive an 06 F250 with stock 265/70 R17s, and my current tyres are 275/65 R18. supposed to be 70 aspect ratio, but the 65s are what the truck...
View Articleorficie tube
Any idea how to get this apart for service. I have the system apart to change some AC component's. Is there a coupler release tool or something. Also I got the replacement orifice from Auto zone. I'm...
View ArticleOdds in our favor???
Are the odds in our favor after we do head studs and oem gaskets as well as getting the heads checked for flatness? What's the chances of blowing gaskets again after all this?
View Articleair conditioner help
ok a/c works good going down the road with rpms up air is 47* but at idle or slow moving traffic air is around 65* coming out of center vent and 90* outside. So is it just time to replace the a/c...
View Article2013 Platinum with 8" Pro Comp
Just ordered an 8" pro comp for my 2013 Platinum will post pics once installed What size tires are you guys able to run with this lift? What width/backspacing on the wheels is working best?
View Articledownpipe flange rotted at the cat
I still have the stock downpipe on my truck, the flange where it connects to the cat is rotted away pretty bad, so I was looking at split flanges as a cob job solution (anyone ever have luck with...
View Articledana 50 spindle nut probs
my 1995 f250 4x4 dana 50 front bearing is blown out and I don't know what 6 point socket that I need to take off the brake hub off the spindle.... does anyone have any ideas ???????????
View ArticleP1298 IDM Fail.
I'm working on a 1999 F350 7.3 DSL. It misses pretty bad. I ran all self tests with the tuner installed and on the KOEO test I found hard fault P1298 present. I was sent to PPT-KA1 and was advised to...
View Article99 f350 4r100 No O/D
Hey really need help with my 4r100 Trans. It was built 9 years ago by ats and has the stage 5 setup. Recently i blew up my reverse, bought a rebuild kit and all the required pieces to fix said trans....
View ArticleStart rough idle stall no start
03 F350 100k. Last week I was driving around and stopped at the inlaws while letting the truck idle is started. First rough idle so I started heading home. Took it up the highway and it didn't like the...
View Article4 new injectors, crank time has trippled
I installed 4 new injectors; 2-4-6-8 because two or three of them were going pretty negative on the contribution test. I had replaced the D-plug & Stand pipes with the upgraded set like 3k miles...
View ArticleDead heading (i.e. no return flow) may not be a good idea
I was thinking after dead heading my system (two tanks, check valves, usual setup for a powerstroke), that this may not be a good idea. The whole idea behind diesel injection is extreme clean fuel...
View ArticlePlumbing 500 gallon pasture spray rig- fluid engineering question
Latest Project is ready to plumb. Pasture spray rig with a 500 gallon poly tank on a tandem walking axle frame from a fertilizer spreader. Will use a 8 roller pto driven pump with 3/4 inlet and outlet....
View ArticleUrgent help needed
I've got an f250 with problems. Build date 08/03. Two main problems here. One was #4 injector solenoid nut backed off the bolt and ruined the injector. So I got that injector replaced and I test drove...
View ArticleHow bad can it get
I have dumped so much money into my truck this year and tonite I figure out my shimmy is coming from my rear end. My yoke started dripping a couple weeks ago and I have been to busy to investigate....
View ArticleTurbo leak? Help!!!
Turbo is leaking. I hear it when I'm working the motor. I made a tool that is pressurized by my air compressor. I hooked it up and started feeling air come from around the intake side area of the...
View Article