Clik here to view.
2004 250 6.0 truck
Great running 6.0 motor with 126,000 miles on it complete from fan to turbo. No blow by. Runs strong, new egr cooler, Had oil changed every 5000 miles. $5000.00. This is the later engine with the icp...
View Articlerunning board on a 03 f250
I have a 03 f250 that is new to me. two days into owning it i took a corner too sharp and broke the running board off. The board is fine, but the brackets that secure it to the underside of the truck...
View ArticleFrustrated and at a loss for diagnosis
I have a 2009 F250 PSD with the 6.4 in it. took it on my first long trip towing our 7000 lb travel trailer (1300 mi round trip from NC to Disney and back). Ran about 60-75 mph the whole way pulling the...
View ArticleCrankcase Breather Tube?
Hi, everyone, my 2003 6.0L Powerstroke giving a MAF code, I cleaned MAF sensor, still there, then found out that Breather tube(one goes from valve cover into air intake ) broken and does not seat...
View ArticleRear blocks
My buddy just came across some 350 rear blocks (2000) from an extended cab short box. My truck happens to be an F250 extended cab long box (2002). I was wondering what the difference really is because...
View ArticleBulletproof Oil Cooler DELTA DATA Needed
I am shopping oil coolers for my 03 6.0 (Bone Stock) and I am stuck between the bulletproof kit and the kit from IPR research. I like the idea of the IPR kit alot and am leaning toward it. I espicaly...
View ArticleMAF Code! Need Help Please
Hi, everyone, my 2003 6.0L Powerstroke giving a MAF code, I cleaned MAF sensor, still there, then found out that Breather tube(one goes from valve cover into air intake ) broken and does not seat...
View ArticleRear hub slinger 2001 Excursion 175K. Are they critical to lubrication?
While servicing my rear parking brakes I had to pull the hubs and replace seals. Replaced bearings while I was in there. Passenger side had a slinger and drivers side did not. Is the slinger critical...
View ArticleHigh pressure powersteering line and pumps
I got a question here... I am getting tired of going through pumps, I cannot get a new HP line as mine is different than any parts house or dealer parts dpt has. My line has the same fittings on each...
View ArticleEBPD control rod
Its taken me two months to get my oil pan job finished. Held up with broken parts and new parts being held at the border. Finally buttoning everything back together tonight and I cannot find the EBPD...
View ArticleWater Separator
Hey Guys, I've a 1987 6.9 in a F250 4x4. I'm pretty sure my water separator is toast. I'm thinking of doing an upgrade of some sort, and maybe something that involves and upgrade to the fuel filter set...
View Articleedge insight alerts
just got a edge insight installed on my 2007 f250 a week ago. i turned on the alerts today and the injpwr turned red and it had 49.0 v. is something wrong or did i do something wrong to cause a alert?...
View ArticleClik here to view.
Bearing Puller from Just Differentials!
Bearing puller tool from Just Differentials! Besides everything you need to stuff your axle housings we also offer the tools needed to help you change your gears. Check out our bearing pullers: Side...
View ArticleHELP
Had an issue with 2008 F250 PSD last week. Had slight surging when leaving campground at 5 mph. When tried to accelerate seemd like it was bogging down. No lights showing on dash. Did improve after...
View ArticleHI from North Florida
new in this, retired with a lot of experience. hope to help some one.
View ArticleReplacing front-outer U-joints
Hey everyone, I did some searching, but the search function only gives me results for ball joints. Is there a write up anywhere on this? Front outer U-joints on a 1996 4X4. I am slightly mechanically...
View ArticleHoneywell/garrett turbo for Detroit diesel
Part number is 23503264. It is in never been used condition. It still has the rubber caps that cover the open pieces. There is nothing wrong with it. It is in immaculate condition. ive seen these go...
View ArticleAnother E4OD problem Code 74
Alright guys, new here. I just picked up a 1994 IDI for a decent price. It has a transmission trouble and before i took too a trans shop i did some research. I am very mechanically inclined just so you...
View Article