possible bad rear main seal
im leaking a good bit of oil from what appears to be the main seal, i have yet to verify if it is the oil sending unit or something in the valley. but assuming it is the rear main can i do the seal and...
View ArticleHPOP
Hello all, I just finished the install of my new HPOP, and after a bit of struggle I got the lines to snap on the fittings on the pump.... hopefully they are seated properly.... My question is there a...
View ArticleNEEDED- Drivers side bucket seat brackets '12 F350 lariat
Just the 4 brackets needed, any help would be greatly appreciated. :thumbsup:
View ArticleClik here to view.
CDR for 6.9 turbo and tube
I have searched many forums and can not find the rubber part that goes from the CDR to the pan for the ATS turbo on a 1986 6.9, can someone get me the part number for a 6.9 1986. Here is what I have...
View ArticleRotella T6 rebate
I'm not sure if this is a good place to post this. I was in Walmart yesterday and the gallon jugs of Rotella T6 have a $5 rebate sticker on them until the end of May. You need to mail in the rebate...
View ArticleFelt Gasket in Air Box
Good day to all. I own a 2010 F350, 6.4 L Superduty. I purchased it new and it currently has 17K miles on it. I pulled the air filter out of it and underneath the filter was a small twisted felt type...
View Article99 cutlass problem
i know this is far from a diesel, but this is my favorite site for knuckle busters :) I bought a 99 olds cutlass to fix up and resell. it had been sitting for 3 years. I changed the fuel filter and put...
View ArticleBanks Intercooler kit 7.3
7.3 Banks inter cooler kit with boot kit and pipes. brand new never installed fits 2000-2003 7.3 superduty make me a fair offer. Dave 484-614-0471
View ArticleBrake Controller for F350 SD
I have a 2002 F350 crewcab 4x4, with a receiver hitch and the big trailer plug harness (6 or 7 pin not sure). It has stock suspension and tires. I want to pull a 30' travel trailer on the hitch. 1) How...
View ArticleIntermittent coolant leak.
Having an odd issue with my 04. It has developed a small but intermittent coolant leak. I can see a small amount of coolant just under the turbo, below/behind the egr valve, near that egg shaped plate...
View ArticleRepair Hub Assembly
Is there any possibility to change the bearing in the Hub Assembly ?:sick:
View Article6.0L Starts and Dies
:ford: 2003 f 250 6.0 powerstroke. After sitting over night 1st start on truck motor starts then dies. Will restart again after cranking for awile and will run and start fine for the rest of the day....
View ArticleWarn Engine
Ok, so the HPOP replacement went well, but when I got it running, (which was uneventful) the Warn Engine light came on with a code of 313 (oil pressure) which I think is a normal thing to happen........
View Articlestart up
When i start the truck up sometimes it immediatly starts up after several spins of the crank but then other times it takes longer crank times. What would casue this? Thanks
View ArticleClik here to view.
Newbie needs help
Hey guys, I am new here and have a few questions. Can someone tell me what the part is in this picture beside the intake heater that has the connector with the green and red tubes on the left and the...
View ArticleTailgate Stripper Pole Cover Replacement
Ok...I've been pointed in the right direction now. When I get the new 350, I am getting rid of the stripper pole! I have found online and in forums with some peeps that have done it, but only replacing...
View ArticleHow long can i drive it?
got a shuttle bus w 6.0L w oil in the coolant. Its clear the oil cooler is junk, can i drive this for another 100 miles or so to a buddies to get fixed or do i risk a catastrophic failure? Its pretty...
View ArticleClik here to view.
Dome light
The spotlight feature in my 94 f250 doesn't work (both sides), regulare dome light works fine. I changed the bulbs in both spotlights still nothin. Not sure if maybe it's the switches? I have a few...
View Articlenew leaf springs
I need to replace the front springs on my truck and was wondering where would be the best place to get them
View ArticleNeed to buy weld in egt sensor bungs
I need to find bungs to weld on my dpf delete pipe for the egt sensors to be installed. I was just wondering where to look online or if anyone knew what thread type they are maybe I could just have...
View Article